Pass Benchmark: 70% • Standard: USCG NMC / 46 CFR

USCG Engine General (Supplementary) (Set 22)

30:00

|

Question 1 of 30

Question Navigator

Correct Incorrect Pending Starred

Question 1 of 30

In accordance with international MARPOL Annex V regulations and federal regulations under 33CFR Subchapter O, the prohibition of the discharge of unground paper products, rags, glass, metal, bottles, and crockery applies to a vessel operating within how many nautical miles of the nearest land?

Browse Questions in Set 22

30 MCQs

#1 In accordance with international MARPOL Annex V regulations and federal regulations under 33CFR Subchapter O, the prohibition of the discharge of unground paper products, rags, glass, metal, bottles, and crockery applies to a vessel operating within how many nautical miles of the nearest land? #2 In accordance with international MARPOL Annex V regulations and federal regulations under 33CFR Subchapter O, the prohibition of the discharge of ground paper products, rags, glass, metal, bottles, and crockery applies to a vessel operating within how many nautical miles of the nearest land? #3 In accordance with international MARPOL Annex V regulations and federal regulations under 33CFR Subchapter O, the discharge or disposal of garbage on vessels of 400 gross tons and above engaged in commerce requires recordkeeping. Which of the following discharge or disposal operations requires a detailed description of the contents of the garbage? #4 Under the federal regulations of 33CFR Subchapter O, what is the definition of the term "sewage"? #5 Under the federal regulations of 33CFR Subchapter O, what is the definition of a "Type I Marine Sanitation Device"? #6 Under the federal regulations of 33CFR Subchapter O, what is the definition of a "Type II Marine Sanitation Device"? #7 Under the federal regulations of 33CFR Subchapter O, what is the definition of a "Type III Marine Sanitation Device"? #8 Under the federal regulations of 33CFR Subchapter O, if a vessel equipped with a Type III Marine Sanitation Device enters a body of water where the discharge of untreated sewage is prohibited, which of the following methods of securing the device to prevent the discharge of sewage is UNACCEPTABLE? #9 Under the federal regulations of 33CFR Subchapter O, if a vessel equipped with a Type II Marine Sanitation Device enters a body of water where the discharge of treated or untreated sewage is prohibited, which of the following methods of securing the device to prevent the discharge of sewage is ACCEPTABLE if it is impractical to close the seacock and prevent its opening? #10 In accordance with the international MARPOL Annex VI regulations, the sulphur content of any fuel oil used on board ships shall not exceed what percentage by weight? #11 In accordance with the international MARPOL Annex VI regulations, in the absence of an exhaust gas cleaning system, what is the maximum allowable sulphur content for a fuel to be burned while the ship is operating in an emissions control area? #12 In accordance with the international MARPOL Annex VI regulations, which of the listed substances is prohibited from being burned in a shipboard incinerator? #13 In accordance with the international MARPOL Annex VI regulations, which of the listed substances is prohibited from being burned in a shipboard incinerator? #14 In accordance with the international MARPOL AnnexVI regulations, what is the minimum allowable flue gas outlet temperature for a continuous-fed shipboard incinerator while in operation? #15 In accordance with the international MARPOL Annex VI regulations, what is a permissible alternative to burning oil residue sludge in an appropriate incinerator? #16 The tool shown in the illustration is called a __________. GS-0072 #17 The lathe tool shown as figure "U" in the illustration is commonly known as a/an __________. GS-0090 #18 Which of the illustrated lathe tools would be used to produce a smooth finish cut for figure I? GS-0009 #19 The lathe tool shown as figure "T" in the illustration is commonly known as a/an __________. GS-0090 #20 The lathe tools shown as figure "M" in the illustration are commonly known as __________. GS-0090 #21 Which single illustrated lathe tool could be used to turn down the stock in figure II? GS-0009 #22 The lathe tool shown as "Q" in the illustration is a __________. GS-0090 #23 Which of the illustrated figures represents the use of a right hand roughing tool? GS-0090 #24 The lathe tool shown as figure "R" in the illustration would best be used to __________. GS-0090 #25 If the distances "A" and/or "B" as shown in the illustration are excessively increased, the tool will __________. GS-0085 #26 The taper produced by a lathe taper attachment is determined by setting the __________. #27 Which of the following definitions accurately describes 'tool feed' when referring to lathe work? #28 For proper support when turning a long thin piece of work between lathe centers, you should use a __________. #29 Work that cannot readily be mounted between lathe centers is usually held in a __________. #30 Which of the lathe operations listed is best done with the carriage locked in position?

Question Discussion & Notes

0

Have a doubt, memory trick, or exam update? Share your insights with fellow mariners.

Loading mariner discussions...